ñEdition: Hans Turck GmbH & Co.KG ñD-45472 Mülheim an der Ruhr ñWitzlebenstraße 7 ñTel. 0208 4952-0 ñFax 0208 4952-264 ñ
[email protected] ñwww.turck.com
Inductive sensor Bi1,5-EG08K-AP6X
M8 x 1 13/4 LED
22
●
threaded barrel, M8 x 1
●
stainless steel, 1.4404
●
3-wire DC, 10…30 VDC
●
normally open, pnp output
●
cable connection
Wiring diagram
1,6
pnp
Bi1,5-EG08K-AP6X 4669040
Rated operating distance Sn Mounting condition Assured sensing range Correction factors Repeatability Temperature drift Hysteresis Ambient temperature
1.5 mm flush ð (0,81 x Sn) mm St37 = 1, V2A ~ 0.7, Ms ~ 0.4, Al ~ 0.3 ð 2% ð ± 10 % 3… 15 % -25…+ 70 °C
Operating voltage Residual ripple
10… 30VDC ð 10 % Uss
DC rated operational current No-load current I0
ð 150 mA ð 15 mA
Residual current Rated insulation voltage Short-circuit protection Voltage drop at Ie
ð 0.1 mA ð 0.5 kV yes / cyclic ð 1.8V
Wire breakage / Reverse polarity protection Output function Switching frequency
yes / complete 3-wire, normally open, pnp ð 3 kHz
Housing Dimensions Housing material Material active face End cap Tightening torque of housing nut Connection Cable quality Cable cross section: Vibration resistance Shock resistance Degree of protection
threaded barrel, M8 x 1 23.6 mm metal, AISI 316L plastic, plastic, PA12-GF20 plastic, PP 10 Nm cable Ø 4, LifYY-11Y, PUR, 2 m 3 x 0.25mm2 55 Hz (1 mm) 30g (11 ms) IP67
Display switch state
LED yellow
+
BU
BK
Functional principle Inductive sensors are designed for wear-free and non-contact detection of metal objects. For this purpose they use a high-frequency electro-magnetic AC field that interacts with the target. Conserning inductive sensors, this field is generated by an LC resonant circuit with a ferrite core coil.
ñEdition: • 25.11.2008
Type Ident-No.
BN
Hans Turck GmbH & Co.KG ñD-45472 Mülheim an der Ruhr ñWitzlebenstraße 7 ñTel. 0208 4952-0 ñFax 0208 4952-264 ñ
[email protected] ñwww.turck.com
ñEdition: Hans Turck GmbH & Co.KG ñD-45472 Mülheim an der Ruhr ñWitzlebenstraße 7 ñTel. 0208 4952-0 ñFax 0208 4952-264 ñ
[email protected] ñwww.turck.com
Inductive sensor Bi1,5-EG08K-AP6X
Mounting instructions Distance D Distance W Distance T Distance S Distance G
minimum distances 2xB 3 x Sn 3xB 1,5 x B 6 x Sn
Diameter of the active area B
Ø 8 mm
T
G
S D
ñEdition: • 25.11.2008
W
Hans Turck GmbH & Co.KG ñD-45472 Mülheim an der Ruhr ñWitzlebenstraße 7 ñTel. 0208 4952-0 ñFax 0208 4952-264 ñ
[email protected] ñwww.turck.com
ñEdition: Hans Turck GmbH & Co.KG ñD-45472 Mülheim an der Ruhr ñWitzlebenstraße 7 ñTel. 0208 4952-0 ñFax 0208 4952-264 ñ
[email protected] ñwww.turck.com
Inductive sensor Bi1,5-EG08K-AP6X
Accessories Type code BST-08B
IdentNo. 6947210
Short text
Dimension drawing
fixing clamp with dead-stop; material: PA6 M3
7,4
4
12
20
ø8
QM-08
6945100
quick-mount fixing clamp with dead-stop; material: chrome-plated brass male thread M12 x 1. Note: The switching distance of proximity switches can be reduced by the use of quick mounting brackets.
17/4 M12 x 1 17,5 32
ø8
MW-08
6945008
16
mounting bracket; material: stainless steel A2 1.4301 (AISI 304)
8,7
5,5
9,5
7,9
7,9 15,9 31,8
11,9 1,8
BSS-08
6901322
7,1
25,4
28,7
fixing clamp; material: polypropylene 5 20 ø8 26,5 30
ñEdition: • 25.11.2008
34
Hans Turck GmbH & Co.KG ñD-45472 Mülheim an der Ruhr ñWitzlebenstraße 7 ñTel. 0208 4952-0 ñFax 0208 4952-264 ñ
[email protected] ñwww.turck.com