INSTRUCTIONS – REV. B
120 Volts/15 Amps/60Hz
120 Volts/15 Amps/60Hz
Apollo 2 Day/Night Cycle Timer
Apollo 2 Easy Guide
oto Photocell cell
Ap Da
ol
y/N
igh
Apollo 2 lo
t Cy
cle
Day/Night Cycle Timer
2
Tim
er
Apollo 2
®
Cycle Timer with Photocell
Ph
120 Volts/15 Amps/60Hz
Photocell
120 Volts/15 Amps/60Hz
Light sensor (photocell): see Optional settings
Photocell
®
Day/Night Cycle Timer
Step 1
Step 2
Set values for ON time & OFF time
Plug into 120VAC outlet Connect equipment to be controlled
ON Time: Duration for which equipment will run
Installation is now complete
OFF Time: Duration in between ON times
OPTIONAL SETTINGS
Photocell
Photocell
Photocell
Photocell
Day/Night Cycle Timer
Apollo 2 Day/Night Cycle Timer
Action 2
Apollo 2
Apollo 2
Day/Night Cycle Timer
Day/Night Cycle Timer
C
C
Note: This unit has been set to perform day only control. For night only or 24 hour control, refer to ‘Optional’ settings.
B
120 Volts/15 Amps/60Hz
Apollo 2
Action 1
A
120 Volts/15 Amps/60Hz
B
120 Volts/15 Amps/60Hz
120 Volts/15 Amps/60Hz
A
Change to ‘24 hour’ control
Change to ‘day only’ control
A. Set both values to minimum B. P lug in, then set both values to maximum within 5 seconds C. O utput light turns on or off according to actual setting D. F ollow instructions as shown in Step 1 & 2
A. Set both values to maximum B. Plug in, then set top value to minimum (Action 1), followed by bottom value to minimum (Action 2) within 5 seconds C. Output light turns on or off according to actual setting D. Follow instructions as shown in Step 1 & 2
Photocell
Photocell
Action 2
B
120 Volts/15 Amps/60Hz
120 Volts/15 Amps/60Hz
A Apollo 2 Day/Night Cycle Timer
Apollo 2 Day/Night Cycle Timer
®
Action 1
C VANCOUVER, W ASHINGTON U.S.A.
Change to ‘night only’ control A. Set both values to maximum B. P lug in, then set bottom value to minimum (Action 1), followed by top value to minimum (Action 2) within 5 seconds C. O utput light turns on or off according to actual setting D. F ollow instructions as shown in Step 1 & 2
www.titancontrols.net For technical assistance call us at 1-888-80-Titan or 1-888-808-4826.
INSTRUCCIONES - REV. B
Apollo 2 Day/Night Cycle Timer
Apollo 2 Guía sencilla
oto Photocell cell
Ap Da
ol
y/N
igh
Apollo 2 lo
t Cy
cle
Day/Night Cycle Timer
2
Tim
er
Apollo 2
®
Temporizador de ciclos con celda fotoeléctrica
Ph
120 Volts/15 Amps/60Hz
120 Volts/15 Amps/60Hz
Photocell
120 Volts/15 Amps/60Hz
Photocell
®
120 Volts/15 Amps/60Hz
Sensor de luz (celda fotoeléctrica): consulte la sección de Configuraciones opcionales
Day/Night Cycle Timer
Paso 1
Paso 2
Fije los valores para el tiempo de actividad (ON) y de inactividad (OFF) Tiempo de actividad (ON): Duración del funcionamiento del equipo Tiempo de inactividad (OFF): Duración entre los tiempos de actividad
Enchufe a un tomacorriente de 120 VAC Conecte el equipo que se va a controlar La instalación se ha completado
CONFIGURACIONES OPCIONALES
Photocell
Photocell
Apollo 2 Day/Night Cycle Timer
#2
Apollo 2
Apollo 2
Day/Night Cycle Timer
Day/Night Cycle Timer
C
C Cambio a control durante “24 horas”
Cambio a control durante el “día únicamente”
A. Fije ambos valores al mínimo B. E nchufe, luego fije ambos valores al máximo en los 5 segundos siguientes C. L a luz de salida se enciende o se apaga conforme a la configuración real D. Siga las instrucciones descritas en el Paso 1 y 2
A. Fije ambos valores al máximo B. Enchufe, luego fije el valor más alto al mínimo (# 1) y el valor más bajo al mínimo (# 2) en los 5 segundos siguientes C. La luz de salida se enciende o se apaga conforme a la configuración real D. Siga las instrucciones descritas en el Paso 1 y 2
Photocell
#2
Photocell
A
B
120 Volts/15 Amps/60Hz
120 Volts/15 Amps/60Hz
Nota: Esta unidad ha sido configurada para funcionar como control durante el día únicamente. Para obtener información sobre el control durante la noche únicamente o sobre el control las 24 horas, consulte la sección de Configuraciones “opcionales”.
B
120 Volts/15 Amps/60Hz
Day/Night Cycle Timer
A
120 Volts/15 Amps/60Hz
B
120 Volts/15 Amps/60Hz
120 Volts/15 Amps/60Hz
A Apollo 2
#1
Photocell
Photocell
Apollo 2 Day/Night Cycle Timer
Apollo 2
#1
®
Day/Night Cycle Timer
C Cambio a control durante la “noche únicamente” VANCOUVER, W ASHINGTON U.S.A.
A. Fije ambos valores al maximo B. E nchufe, luego coloque el valor más bajo al mínimo (# 1) y el valor más alto al mínimo (# 2) en los 5 segundos siguientes C. L a luz de salida se enciende o se apaga conforme a la configuración real D. Siga las instrucciones descritas en el Paso 1 y 2
www.titancontrols.net Para obtener asistencia técnica, llámenos al 1-888-80-Titan o al 1-888-808-4826.