INSTRUCTIONS – REV B
Light sensor (photocell): see Optional settings
Photocell
®
120 Volts/15 Amps/60Hz
120 Volts/15 Amps/60Hz
Apollo 12
Day/Night Short Cycle Timer
®
Apollo 12 Short Period Cycle Timer with Photocell
Easy Guide
Ph
oto
cell
120 Volts/15 Amps/60Hz
Photocell
Da
Ap
y/N
igh
ol
t Sh
ort
lo Cy
cle
12
Tim
er
Apollo 12 Day/Night
Short Cycle Timer
Step 1
Step 2
Set Values ON time OFF time
Plug into 120VAC outlet. Connect equipment to be controlled.
ON Time: Duration for which equipment will run.
Installation is now complete
OFF Time: Duration in between ON times.
OPTIONAL SETTINGS
Photocell
Photocell
120 Volts/15 Amps/60Hz
Apollo 12
Day/Night Short Cycle Time r
B
Apollo 12
Day/Night Short Cycle Time r
Apollo 12
B
Action 2
Apollo 12
Day/Night Short Cycle Time r
Day/Night Short Cycle Time r
C
C
Note: This unit has been set to perform 24 hour control. For night or day only control, refer to ‘Optional’ settings.
Action 1
A 120 Volts/15 Amps/60Hz
A
120 Volts/15 Amps/60Hz
120 Volts/15 Amps/60Hz
Photocell
Photocell
Change to 24 hour control
Change to day only control
A. Set both values to minimum B. P lug in, then set both values to maximum within 5 seconds C. O utput light turns on or off according to actual setting D. F ollow instructions as shown in Step 1 & 2
A. Set both values to maximum B. Plug in, then set top value to minimum, (Action 1) followed by bottom value to minimum, (Action 2) within 5 seconds C. Output light turns on or off according to actual setting D. Follow instructions as shown in Step 1 & 2
Photocell
120 Volts/15 Amps/60Hz
120 Volts/15 Amps/60Hz
Photocell
Action 2
A Apollo 12
Day/Night Short Cycle Time r
B Apollo 12
Day/Night Short Cycle Time r
®
Action 1
C VANCOUVER, W ASHINGTON U.S.A.
Change to ‘night only’ control A. Set both values to maximum B. P lug in, then set bottom value to minimum, (Action 1) followed by top value to minimum (Action 2) within 5 seconds C. O utput light turns on or off according to actual setting D. F ollow instructions as shown in Step 1 & 2
www.titancontrols.net For technical assistance call us at 1-888-80-Titan or 1-888-808-4826.
INSTRUCCIONES - REV. B
Photocell
Apollo 12 Temporizador de ciclos de períodos cortos con celda fotoeléctrica
Guía sencilla
Ph
120 Volts/15 Amps/60Hz
®
120 Volts/15 Amps/60Hz
Photocell
Apollo 12
Day/Night Short Cycle Timer
oto
cell
120 Volts/15 Amps/60Hz
®
Sensor de luz (celda fotoeléctrica): consulte la sección de Configuraciones opcionales
Da
Ap
y/N
igh
ol
t Sh
ort
lo Cy
cle
12
Tim
er
Apollo 12 Day/Night
Short Cycle Timer
Paso 1
Paso 2
Fije los valores para el tiempo de actividad (ON) y de inactividad (OFF) Tiempo de actividad (ON): Duración del funcionamiento del equipo
PEnchufe a un tomacorriente de 120 VAC Conecte el equipo que se va a controlar
Tiempo de inactividad (OFF): Duración entre los tiempos de actividad
La instalación se ha completado
CONFIGURACIONES OPCIONALES
Photocell
Photocell
120 Volts/15 Amps/60Hz
Apollo 12
Day/Night Short Cycle Time r
#1
A 120 Volts/15 Amps/60Hz
B
120 Volts/15 Amps/60Hz
120 Volts/15 Amps/60Hz
Photocell
Photocell
A
Apollo 12
Day/Night Short Cycle Time r
Apollo 12
B #2
Apollo 12
Day/Night Short Cycle Time r
Day/Night Short Cycle Time r
C
C
Cambio a control durante el “día únicamente”
Cambio a control durante “24 horas”
A. Fije ambos valores al máximo B. Enchufe, luego fije el valor más alto al mínimo (# 1)y el valor más bajo al mínimo (# 2) en los 5 segundos siguientes C. La luz de salida se enciende o se apaga conforme a la configuración real D. Siga las instrucciones descritas en el Paso 1 y 2
A. Fije ambos valores al mínimo B. E nchufe, luego fije ambos valores al máximo en los 5 segundos siguientes C. L a luz de salida se enciende o se apaga conforme a la configuración real D. Siga las instrucciones descritas en el Paso 1 y 2
Photocell
#2
Photocell
A 120 Volts/15 Amps/60Hz
120 Volts/15 Amps/60Hz
Nota: Esta unidad ha sido configurada para funcionar como control durante las 24 horas. Para obtener información sobre el control durante la noche únicamente o durante el día únicamente, consulte la sección de Configuraciones “opcionales”.
Apollo 12
Day/Night Short Cycle Time r
B Apollo 12
#1
Day/Night Short Cycle Time r
®
C Cambio a control durante la “noche únicamente” VANCOUVER, W ASHINGTON U.S.A.
A. Fije ambos valores al mínimo B. E nchufe, luego coloque el valor más bajo al mínimo (# 1) y el valor más alto al mínimo (# 2) en los 5 segundos siguientes C. L a luz de salida se enciende o se apaga conforme a la configuración real D. Siga las instrucciones descrita s en el Paso 1 y 2
www.titancontrols.net Para obtener asistencia técnica, llámenos al 1-888-80-Titan o al 1-888-808-4826.