INSTALLATION INSTRUCTIONS
NS1D12P
NS1D12F
NS1D12S
S1 Racks Doors Spanish Product Description German Product Description Portuguese Product Description Italian Product Description Dutch Product Description French Product Description
NS1D12-20-28-36-41
NS1D12-20-28-36-41
DISCLAIMER Milestone AV Technologies and its affiliated corporations and subsidiaries (collectively "Milestone"), intend to make this manual accurate and complete. However, Milestone makes no claim that the information contained herein covers all details, conditions or variations, nor does it provide for every possible contingency in connection with the installation or use of this product. The information contained in this document is subject to change without notice or obligation of any kind. Milestone makes no representation of warranty, expressed or implied, regarding the information contained herein. Milestone assumes no responsibility for accuracy, completeness or sufficiency of the information contained in this document.
Installation Instructions
LEGEND Tighten Fastener Apretar elemento de fijación Befestigungsteil festziehen Apertar fixador Serrare il fissaggio Bevestiging vastdraaien Serrez les fixations Loosen Fastener Aflojar elemento de fijación
Chief® is a registered trademark of Milestone AV Technologies. All rights reserved.
Befestigungsteil lösen Desapertar fixador Allentare il fissaggio Bevestiging losdraaien
IMPORTANT WARNINGS AND CAUTIONS!
Desserrez les fixations Open-Ended Wrench Llave de boca
WARNING: A WARNING alerts you to the possibility of serious injury or death if you do not follow the instructions.
Gabelschlüssel Chave de bocas Chiave a punte aperte
CAUTION: A CAUTION alerts you to the possibility of damage or destruction of equipment if you do not follow the corresponding instructions.
Steeksleutel Clé à fourche Phillips Screwdriver
WARNING: Failure to read, thoroughly understand, and follow all instructions can result in serious personal injury, damage to equipment, or voiding of factory warranty! It is the installer’s responsibility to make sure all components are properly assembled and installed using the instructions provided.
Destornillador Phillips Kreuzschlitzschraubendreher Chave de fendas Phillips Cacciavite a stella Kruiskopschroevendraaier Tournevis à pointe cruciforme
2
Installation Instructions
NS1D12-20-28-36-41
TOOLS REQUIRED FOR INSTALLATION
7/16"
#2
PARTS
A (1) [Door]
OR
OR
[Perforated]
[Solid]
(NS1D12F shown)
(NS1D12S shown)
[Plexiglass] (NS1D12P shown)
E (2) 1/4-20 x 5/8" F (2) 1/4-20
C (1) [Top door support]
B (1) [Door catch]
D (1) [Lower door support]
3
NS1D12-20-28-36-41
Installation Instructions
INSTALLATION IMPORTANT ! : If installing doors and side panels (not included) on an S1 rack, the doors must be installed before installing the side panels. 1.
Remove and save four screws from both top and bottom of rack front. (See Figure 1)
IMPORTANT ! : If the door is to be attached with the pullring handle on the right side, the two nuts and grounding wire already installed on the door must be removed and reinstalled on the opposite end of the door before the door is installed. The grounding wire should be on the BOTTOM of the installed door. (See Figure 3)
Move to grounding screw
Move two nuts and grounding wire
x8
1
(NS1D12F shown)
NOTE: Door will be flipped before installation.
Figure 1 2. 3.
Add top door support (C) and lower door support (D) to rack front. (See Figure 4) Attach door supports using eight screws removed in Step 1.
Figure 3 4.
Rotate two spring handles (one at bottom and one at top) on inside of door. (See Figure 4) (View from back of door)
(C)
Upper spring handle
(D)
5
Lower spring handle
3
x8 (NS1D12F shown)
Figure 2
4
4 Figure 4
Installation Instructions 5. 6.
NS1D12-20-28-36-41
Pull down on upper spring handle, and push up on lower spring handle. Insert door into rack, aligning the spring handle ends with the holes in the door support at top and bottom of rack. (See Figure 5)
9
(E) x 2
Spring handle end Door support (F) x 2
6
Door
(B)
Figure 7 Figure 5 7.
Push spring handle end into door supports, and re-latch spring handle.
8.
Determine location for door catch (B) by matching up handle cut-out in door with correct position on rack. (See Figure 6)
10. Loosen screw in lower door support, attach door grounding wire, and tighten screw to finish connection. (See Figure 8)
x1
10
8
Figure 6 9.
Figure 8
Add door catch (B) to rack rail using two 1/4-20 x 5/8" screws (E) and two 1/4-20 lock nuts (F). (See Figure 7)
5
NS1D12-20-28-36-41
Installation Instructions
(inside view of door)
Location of grounding lugs
Grounding screw and nut installed at factory
Earthing symbol IEC 60417 No. 5019 affixed adjacent to grounding terminal.
Figure 9
DANGER: IMPROPER WIRING CAN LEAD TO DEATH OR SEVERE PERSONAL INJURY! Grounding must be installed by qualified personnel using a UL Recognized No. 12AWG Green and Yellow grounding wire connected to grounding lug on rack.
6
Installation Instructions
NS1D12-20-28-36-41
7
NS1D12-20-28-36-41
Installation Instructions
USA/International
Europe Chief Manufacturing, a products division of Milestone AV Technologies 8821-002016 Rev02 2012 Milestone AV Technologies, a Duchossois Group Company www.chiefmfg.com 06/12
Asia Pacific
A P F A P F A
6436 City West Parkway, Eden Prairie, MN 55344 800.582.6480 / 952.225.6000 877.894.6918 / 952.894.6918 Franklinstraat 14, 6003 DK Weert, Netherlands +31 (0) 495 580 852 +31 (0) 495 580 845 Office No. 1 on 12/F, Shatin Galleria 18-24 Shan Mei Street Fotan, Shatin, Hong Kong P 852 2145 4099 F 852 2145 4477
