Internal Schematic of the Type CP Relay with Independent Contacts in the Type FT-11 Case. Fig. 1. Type CP ... the case b

4300 Coral Ridge Drive. Coral Springs, Florida 33065. Telephone: +1 954-752-6700. Fax: +1 954-345-5329 www.abb.com/subst

moisture, excessive vibration, and heat. Mount the relay vertically by means of t he four mounting holes on the flange f

change taps requires connecting the lead located in front of the desired setting by means of a screw con- nection. 4.0 E

the normal direction to hold the contacts open. ... contact must be held open until sufficient real power flows ... movi

The CWD relay for three-phase application, senses ... The watt sensing unit settings can be defined either by contact se

Of the line to WhiCh it is conneCted by pulled downward on the front contact end by a measuring the ratio of ..... verif

DEMODULATOR. TIME DELAY (DTD II). MODULE ASSEMBLY - 1603C76602. COMPONENT LOCATION - 1493B68. +1 SD. RFIFS 11. *06. R54 - R55 = *07. D8. C11 c24. C24. TP6. OTP5. 150. +15D-H, -150. R4S- c20. - R46 H-. SD. R35. R48. AHRSB-. 316. C13. R41. 1425. 33

For the type KH-2 relay with separate overcurrent unit, proceed ... The directional overcurrent unit is a product induct

STEP button for about one second, the display .... tion is set and stored in the same way as the address ... signals of the relay module to be activated one by one.

settings and electrical connections. APPLICATION. The KD-3 relay (Figure l) is a single phase impedance type relay conne

If damage is found or suspected, file a claim with the ... Always apply over-current protection on ungrounded input and

ABB Inc. 4300 Coral Ridge Drive. Coral Springs, Florida 33065. Telephone: +1 954-752-6700. Fax: +1 954-345-5329 www.abb.

setting is determined by the sum of per unit values between the R and L lead. ... erating torque as determined by the ph

HEAD OFFICE: Kenwood Limited, 1-3 Kenwood Business Park, New Lane, Havant, Hampshire PO9 2NH. TYPE ZJX740/TYPE ZJX760. T

The type KRQ relay is a high-speed directional over- current ground ... and the overcurrent unit operates on residual cu

ground relay in which the directional unit operates on negative sequence current and voltage, and the over-current .....

taps requires connecting the lead located in front of the tap block to the desired settings by means of a screw connecti

the heating element, buy a suitable descaler and descale your kettle. After descaling ... deposit on the side of the ket

Typ / Type. F 424 S-43/38. F 424 S-43/37 Z. F 424 S-50/45 Z. F 425 S-41/34. F 426 S-41/38. F 427 S3-43/38. F 430 S-41/38. F 430 S-41/37 Z. F 430 S-50/45 Z.

4 on off full lock full low. 370. Series 3 on off. 1. 3. 4. 5. 6. 7. 8. STOP. 10 washable. 2. 9 full low. 360. 370. 360

3. V. OL. T. A. GE FR. BIKE OWNERS MANUAL. E sp. A ñ. OL. contenIDo. Concepto Voltage FR . .... 525 - 571mm. BB housing.

this connection the maximum torque of the relay occurs at 100% P.F. The pickup value is .02 amp at rated voltage and max

e blocco coltelli), premere con una penna a sfera sul tasto reset (9) per almeno 3 secondi per risettare il software. Me