Sceptre X9 Komodo VII Video Motherboard Replacement
ID de guía: 10840 - Borrador: 2014-01-28
Sceptre X9 Komodo VII Video Motherboard Replacement This guide will remove and install the video motherboard.
Escrito por: David Taylor
© iFixit — CC BY-NC-SA
es.iFixit.com
Página 1 de 8
Sceptre X9 Komodo VII Video Motherboard Replacement
ID de guía: 10840 - Borrador: 2014-01-28
HERRAMIENTAS: 2.0mm Flathead Screwdriver (1) 8" Needle Nose Plier (1) iFixit Opening Tools (1)
© iFixit — CC BY-NC-SA
es.iFixit.com
Página 2 de 8
Sceptre X9 Komodo VII Video Motherboard Replacement
ID de guía: 10840 - Borrador: 2014-01-28
Paso 1 — Stand
Place the monitor face down.
Remove the four 11.5mm screws with a #2 Phillips screwdriver.
Remove the stand by pulling it out.
Remove two 11.5mm screws with a #2 Phillips screwdriver.
Remove the plastic bar.
Paso 2
© iFixit — CC BY-NC-SA
es.iFixit.com
Página 3 de 8
Sceptre X9 Komodo VII Video Motherboard Replacement
ID de guía: 10840 - Borrador: 2014-01-28
Paso 3 — Board Cover
Using a #2 Phillips screwdriver, remove the six 7mm screws at the circled locations.
Paso 4
Pry the monitor using the plastic opening tool to release the clips holding the cover on.
There are four clips on each side, four on the top, and one on the bottom. You may hear a loud snapping noise when releasing the clips. Do not be alarmed, it is natural.
Once all the clips have been released, remove the cover by pulling it up.
© iFixit — CC BY-NC-SA
es.iFixit.com
Página 4 de 8
Sceptre X9 Komodo VII Video Motherboard Replacement
ID de guía: 10840 - Borrador: 2014-01-28
Paso 5
Using the #2 Phillips screwdriver, remove the one 6mm screw.
Unplug the indicated cable by pulling on the base.
Slide the cover toward the top of the monitor.
Remove the cover.
© iFixit — CC BY-NC-SA
es.iFixit.com
Página 5 de 8
Sceptre X9 Komodo VII Video Motherboard Replacement
ID de guía: 10840 - Borrador: 2014-01-28
Paso 6 — Video Motherboard
Use caution when removing the connectors as they can easily break when removing.
Disconnect the multi-pin connector at the top of the board by firmly grasping the connector and pulling to the side.
Disconnect the multi-pin connector that runs between the video motherboard and the power supply motherboard. Firmly grasp the connector and pull straight up.
A plastic opening tool can be used to assist in the removal of connectors.
Paso 7
Remove the two 3/16" hex head screws from the VGA connecter. Use a pair of needle nose pliers if a wrench is not available.
© iFixit — CC BY-NC-SA
es.iFixit.com
Página 6 de 8
Sceptre X9 Komodo VII Video Motherboard Replacement
ID de guía: 10840 - Borrador: 2014-01-28
Paso 8
Remove the four 6.4mm #2 Phillips screws from the corners of the motherboard with a #2 Phillips screwdriver.
Paso 9
Lift the motherboard straight up to remove it from the back panel.
To reassemble your device, follow these instructions in reverse order. La versión más reciente de este documento fue generada en 2019-07-09 07:47:17 AM .
© iFixit — CC BY-NC-SA
es.iFixit.com
Página 7 de 8
Sceptre X9 Komodo VII Video Motherboard Replacement
© iFixit — CC BY-NC-SA
ID de guía: 10840 - Borrador: 2014-01-28
es.iFixit.com
Página 8 de 8