Polyester wall-mounting enclosures IP 66
Thalassa PLM
Introduction
Technical characteristics ●M onobloc wall-mounting enclosure made from polyester reinforced with fibreglass, moulded by hot compression, RAL 7032 grey colour. ● Version with transparent tempered-glass door. ● Degree of protection IP 66 according to IEC 60529. ● Resistance to external mechanical impacts: – Plain door enclosures IK 10 (20 joules). – Glazed door enclosures IK 08 (5 joules) according to IEC 62262. ● Locking device outside the sealed area, guaranteeing the tightness of IP 66 over time. ● Locking system: – Enclosure height ≤ 847 mm: 2 locks with double-bar insert or 1 handle with key lock and 3-point closure. – Enclosure height 1056 mm: 1 lock with double-bar insert and 4-point closure. ● Door opening angle: 180°. ● Bosses for accessory-fixing inserts: M6 inside the enclosure, M5 in the door for enclosure heights of 430 and 530 mm, M6 in the door for enclosure heights ≥ 647 mm. ● Fixing of rear accessories on 4 M8 studs, included in the standard supply. ● Direct fixing of symmetrical rails ref. NSYCS●●●PLM, with plastic nuts, ref. NSYTCSPLM, to be installed in the notches on the rear of the body, with a pitch of 25 mm. ● Grid pattern with a pitch of 25 mm on the back of the door.
Built-in canopy protecting the door and the sealing gasket. Two double-bar 3-mm locks outside the sealed zone.
Polyamide hinge pin, easily removable and captive.
External dimensions (mm) Height (A) 430 530 647 747 847 1056
Width (B) 330 430 436 536 636 852
References of wall-mounting enclosures with door
Depth (C)
Plain (3)
Plain (1)
Transparent
Transparent (1)
200 200 250 300 300 350
NSYPLM43 NSYPLM54 NSYPLM64 NSYPLM75 NSYPLM86 NSYPLM108 (2)
NSYPLM43V NSYPLM54V NSYPLM64V NSYPLM75V NSYPLM86V -
NSYPLM43T NSYPLM54T NSYPLM64T NSYPLM75T NSYPLM86T NSYPLM108T (2)
NSYPLM43TV NSYPLM54TV NSYPLM64TV NSYPLM75TV NSYPLM86TV -
(1) Wall-mounting enclosure with handle and lock with 3-point closure and key 1242 E delivered as standard. (2) Wall-mounting enclosure with standard 5-mm double-bar lock and lock with 4-point closure. (3) These enclosures are also available equipped with metallic or insulating mounting plates. See summary guide of the references table on page PLM004_2.
PLM003_
Polyester wall-mounting enclosures IP 66
Thalassa PLM
Dimensions
I N Ø8
M8
H
M
A
V
G K
16
U
E
J
A: Height B: Width C: Depth
L Y
K
D
L
5
Y'
I N Ø8
F
J
H
M
A
V
G K
16
U
O
M8
E
L Y
K
D
L
Bottom screw and door bosses (mm)
Dimensions (mm)
C
F
G
H
I
J
K
L
M
N
O
U
V
181 181 228 278 278 327 M8
247 347 388 487 587 775
150 150 192 241 241 280
179 279 279 379 479 680
168 168 212 261 261 300
325 425 525 Y' 325 725 925
225 15 325 325 425 525 725
375 475 575 675 775 975
150 250 250 350 450 650
13 13 13 15 15 15
273 373 473 573 673 854
194 294 294 394 494 661
H
E
X
E
260 360 360 460 560 760
5
I N
O
D
380 480 580 680 780 980
References NSYPLM43 NSYPLM54 NSYPLM64 NSYPLM75 NSYPLM86 NSYPLM108
16 G K
M
A
V
Glazed door (mm)
F
C 200 200 250 300 300 350
Internal fixing (m)
J
B 330 430 436 536 636 852Ø8
X'
A 430 530 647 747 847 1056
U
L L
C X
5
X'
B
Y
K
D
B
15 Y'
External fixing with lugs (mm) Vertical
X
C X'
B
Horizontal
X
Y
X’
Y’
490 590 690 790 890 1090
225 325 330 430 530 750
355 455 555 655 755 955
360 460 465 565 665 885
References
NSYPLM43 NSYPLM54 NSYPLM64 NSYPLM75 NSYPLM86 NSYPLM108
PLM003_