Technical Data Sheet Long sliding Clips
6
5
4
3
2
1
F
Long sliding clips with sliding range of 75mm 0 75 ,
30,
0
0 ,5
-Material: stainless steel V2A 1.4301 -Sheet thickness: 0,5 mm -VPE: 400 pcs
0
-Available in the following adhesion heights:
00
0 4, 0
Ha f t höh e
88, 44
30 ,
00
6 ,0
,0 0
00 11 0
E
,0 0
• 25mm: Art. Nr.: PHE17025 • 28mm: Art. Nr.: PHE17028 • 30mm: Art. Nr.: PHE17030 • 32mm: Art. Nr.: PHE17032 • 38mm: Art. Nr.: PHE17038 • 50mm: Art. Nr.: PHE17050
D
C
0
Application: Metal roofs and facades are exposed to external environmental influences such as wind and temperature-induced length expansions. To avoid damage a correct positioning of the fixed and sliding clips is required. The laying arrangement of the sliding clips is dependent on the roof inclination and must be taken from the plumbing/tinsmith rules and regulations of the ZVSHK. Note: In all cases the technical regulations (of the respective countries), legal Material: regulations (of the respective countries), statics and local conditions must be observed! Gezeichnet
Datum 27.02.2017
Name Marvin Kiesel
Kontrolliert Norm
DIN 6930-2
2
DB-Schiebehafte_75
6
5
4
Status
Änderungen
3
Datum
Name
B
2
A2
1
Kling Spenglerei GmbH
Tel. +49 8322 4531
[email protected]
Im Steinach 44, D-87561 Oberstdorf
Fax. +49 8322 7586
www.kling-dach.de
A
Technical Data Sheet Long sliding Clips 8
7
6
5
4
3
2
1
F
F
H aft höh e
Gl
E
D
e it
be
r ei
ch
75
mm
Prägung um eine ungewollte Demontage zu vermeiden
E
Prägung um eine korrekte Ausrichtung der Hafte zu erleichtern
Abgerundete Ecken zum Schutz der Dachhaut vor Reibungsschäden
D
Versteifungssicke zur Erhöhung der Stabilität der Hafte und zur Sicherung der Dachhaut vor Reibungsschäden
Ober- und Unterteil der Hafte sind bereits vormontiert C
C
Das Oberteil ist einfach im vorprofilierten Falz einzuhängen und ermöglicht das Einlegen von Dichtbändern B
B
Quality: All long sliding clips are industrially produced with stamping and bending machines. Internal quality controls ensure a consistently high quality of fastening elements. Gezeichnet
Datum 27.02.2017
Name Marvin Kiesel
Material:
Extraction values: DB-Schiebehafte_75 The extraction values of the long sliding clips depend on the quality3 of the roof 2 8 7 6 5 4 1 substructure and the fasteners used. For the clips extraction values of 600N (60kg) can be assumed. However, the maximum clip distance must not exceed 500mm. Kontrolliert
A
Norm
Status
Änderungen
Datum
A
DIN 6930-2
1
A2
Name
Fasteners: The following fastening materials must be used for mounting the long sliding clip: •Grooved nails made of stainless steel according to DIN 1052 and according to load capacity class 3/C ≥ 2.5 x 25mm •Countersunk head screws in stainless steel 4.0 x 25 or 4.0 x 30mm with lead covers
Kling Spenglerei GmbH
Tel. +49 8322 4531
[email protected]
Im Steinach 44, D-87561 Oberstdorf
Fax. +49 8322 7586
www.kling-dach.de
8
Technical Data Sheet Long sliding Clips 7
6
5
4
3
2
1
F
F
Use of noise protection mats: When using noise protection mats under the sheet metal panels, the compressed height of the mat must be adapted to the clip height. In the case of Kling sliding clips, the clip height is adjusted over the lower part and this increases the dimensional stability of the clip when using noise protection mats.
E
Die Hafthöhe wird über das Unterteil angepasst
D
D
Haf t höhe 3 0 mm
C
B
Vollflächige Auflage und durchgehende Lasche erhöhen die Stabilität der Hafte bei der Verwendung von Lärmschutzmatten
C
Installation: Careful assembly of the individual clips is indispensable. Nails, screws, etc. which are protruding from the surface, should be reworked as this could lead to injuries to the roof skin. When using countersunk head screws as fasteners, we recommend using the Fixed Clip Plus with countersunk holes. Gezeichnet
Datum 08.03.2017
Name Marvin Kiesel
Norm
B
Material:
Kontrolliert
A
E
DIN 6930-2
A
DB_Schiebehafte_75_30 1A2
8
7
6
5
4
Status
Richtig right
Änderungen
3
Datum
Name
2
1
Falsch wrong
Kling Spenglerei GmbH
Tel. +49 8322 4531
[email protected]
Im Steinach 44, D-87561 Oberstdorf
Fax. +49 8322 7586
www.kling-dach.de
Technical Data Sheet Long sliding Clips Usability: Long sliding clips are used when the panel length exceeds the maximum permissible panel length for sliding clips with a 55mm sliding range (see material-specific listing). If the material-specific panel length is above the total length shown below, long sliding clips with a 75mm sliding range must be used in the above lying lengths. Through the use of long sliding clips with a 75mm sliding range, the maximum permissible panel lengths can be extended by 35% in a material-specific manner. Maximal zulässige Scharenlänge für Schiebehaften mit 55mm Gleitbereich
• • • • •
Copper - Total length up to 10 m Stainless Steel - Total length up to 14 m Aluminium - Total length up to 10 m Titanzink - Total length up to 10 m Galvanized steel sheet - Total length up to 14 m
Arrangement: The arrangement and the number of fixed clips is dependent on the loads to be absorbed, the inclination of the roof and the expansion possibilities at the ridge and eaves. The fixed clips are arranged on a length of 1 - 3m as shown in the figure below. When using snow and 6 clips must be5 adapted to the 4 loads that are 3 to be 2 solar8 systems, the 7number of fixed expected.
1
F
F
Range of fixed clips depending on the inclination of the roof Bereich der Schiebehaften E
E
Bereich der Schiebehaften H af t a b
sta nd
Bereich der Festpunkthaften
D
C
D
Dachneigung: 0° bis 3°
Dachneigung: 3° bis 10°
n fte eha b e i Sch
C
>30°
>3° -
