installation instructions for - Cooper Industries

DE LAMPE LZR-404. For use with ... Use a narrow blade screwdriver as shown to ... FIG A. 3:5: NM Thumh. Latch. Circuit N

106KB Größe 7 Downloads 125 Ansichten

Kommentar

Empfehlen Sie Dokumente

installation instructions - Cooper Industries

4 oct. 2012 - This can result in twisted wires causing connections to break which can create a shock hazard when powered

ALL-PRO® Installation Instructions for ET-700 ... - Cooper Industries

twisted group of white wires and tighten. Apply electrical tape over the wire nut connector to cover any bare wires. Rep

SNF/SSF Instructions d'installation - Cooper Industries

Apply screws on the sides of channel (T12HO and. Slimline, SSF only). 3. ... Installez les vis sur les côtés du canal (T

LED Nightlight & Receptacle Instructions - Cooper Industries

The LED nightlight receptacle replaces a standard in- wall receptacle ... instructions, or if the wiring does not match

SNF/SSF Instructions d'installation - Cooper Industries

Lamps contain mercury, dispose according to local, state, or federal laws. nOTiCE. If supply wires are located within 3

Full LED Nightlight Instructions — 7737 - Cooper Industries

NOTE - A neutral connection is required in the wall box where the dimmable nightlight is to be installed. Description: •

IF 1652 - Cooper Industries

Sleeve Locking Screw. 13. 'O' Ring. 10. Ground Plate Screws. 9. Brass Retaining Ring. 2. Plug Sleeve. 11. Insulator Asse

sure-lites - Cooper Industries

SURE-LITES 1121 Hwy 74 South Peachtree City, Georgia 30269 770-486-4800 Fax 770-486-4801 7/07 049-73C. INSTALLATION. Ste

warning - Cooper Industries

Risk of fire/electric shock. If not qualified, consult an electrician. • Disconnect .... Lights should turn ON with moti

HALO - Cooper Industries

Faites attention à ne pas les rayer et à ne pas toucher les DEL avec le tournevis. UTILISEZ DES GANTS lors de ce process

Full LED Nightlight Instructions — 7737 - Cooper Industries

To switch to guide light mode, press and hold the light lens for 10 seconds when the nightlight is OFF. Release the ligh

IF 1652 - Cooper Industries

ADVERTENCIA. PELIGRO DE DESCARGA ELÉCTRICA. Para evitar una ... estén dañados. • Controle las conexiones para detectar s

HALO Commercial - Cooper Industries

experiencia en cableado de edificios o por un electricista calificado. El sistema eléctrico y el método de conexión eléc

HALO® HALO - Cooper Industries

afin de répondre aux normes NEC les plus récentes et sont homo- logués UL conformément au UL 1571 OU 1570. Avant d'effec

090954_Hanger_Instr.qxd:Layout 1 - Cooper Industries

OR HANDLING OF THIS PRODUCT. WARNING: NOTE ACTUAL FIXTURE DESCRIPTION OF ANY. SHORTAGE OR NOTICEABLE DAMAGE ON. DELIVERY

Iris squares copy - Cooper Industries

Conservación de Energía - de Nueva York;. Código Internacional de Conservación de. Energía. Conexión Eléctrica. • No dej

Halo Commercial Trims - Cooper Industries

Para retirar el lente o la moldura de frente muerto para el cambio de lÃ¡mpara de la unidad, baje parcialmente la moldur

090989_Socket Instr.qxd:Layout 1 - Cooper Industries

RISK OF FIRE, ELECTRICAL SHOCK, CUTS. AND OR OTHER CASUALTY HAZARDS. THIS PRODUCT MUST BE INSTALLED IN. ACCORDANCE WITH

Installation Instructions For

Sistomas do Rieles Halo oun REGLER LA DOUILLE DE LAMPE. Les supports de lampc Lazer peuvent étre util- isés avec les rai

GalleonTM LED Area/Site Luminaire Installation ... - Cooper Industries

[PDF]GalleonTM LED Area/Site Luminaire Installation ... - Cooper Industrieshttps://s3.amazonaws.com/cesco-content/unilog

Guía del usuario - Cooper Industries

Ahorro de tiempo y energía: apague grupos de luces desde cualquier ubicación en su casa y reduzca las cuentas de electri

091708_0590F035.qxd:Layout 1 - Cooper Industries

wireguard, two clips per side. 4. Install wireguard clip and wireguard to fixture as shown in. Figure 4. 5. Use thumbscr

H270 Inst sht.qxd - Cooper Industries

Supply wire insulation must be rated for at least 90°C. Step 2 Remove the wiring box cover. Remove the appro- priate kno

090989_Socket Instr.qxd:Layout 1 - Cooper Industries

insérant les crevés dans les fentes du canal avec les rails orientés comme dans l'illustration. Figure 1. Trouvez les ra