80 Series Thermostat Wiring Diagrams for 1F80-0471 and 1F86-0471 Single Stage or Heat Pump Figure 1 – Single Stage or Heat Pump with Single Transformer Jumper
O/B
W
Y
G
RH
C
RC
System Single Stage except 3-wire Zone Valve application
See Fig. 3 3-wire Zone Valve application Energized Constantly in either Cool or Heat Mode
Heat Pump
Heat Mode 1st Stage
Cool Mode
Constant
Blower/Circulator Fan Energized Energized in call for Heat or Cool
24 Volt 24 Volt (Hot) (Hot) Heat Cool
24 Volt (Common)
N/A
NEUTRAL 120VAC
24VAC HOT CLASS II TRANSFORMER
Figure 2 – Single Stage or Heat Pump with Two Transformers Jumper (see note)
O/B
W
Y
G
RH
RC
C
System Single Stage except 3-wire Zone Valve application
See Fig. 3 3-wire Zone Valve application
Heat Mode 1st Stage
Constant
24 Volt 24 Volt (Hot) (Hot) Heat Cool
Blower/Circulator Fan Energized
Energized Constantly in either Cool or Heat Mode
Heat Pump
Cool Mode
Energized in call for Heat or Cool
24 Volt (Common)
N/A
NEUTRAL 120VAC
24VAC NEUTRAL 120VAC
HOT
24VAC CLASS II TRANSFORMER
HOT HEATING CLASS II TRANSFORMER
Note: If continuous backlight or hardwired power input are desired but do not function in both HEAT and COOL modes, cut the heating transformer 24V wires and tape off. Connect the neutral circuit disconnected from the heating transformer to the neutral circuit of the cooling transformer. Disconnect the wire to the RH terminal and install a jumper between RH and RC. Depending on the system requirements, replace the cooling transformer with a 75VA class II transformer if needed.
Figure 3 – 3-Wire (SPDT) Heat Only Zone Valve Wiring Jumper
O/B
Y
W
G
Opens Valve (4)
Blower/Circulator Fan Energized
RH
RC
C
System
Single Stage 3-wire Zone Valve application
Constant
Closes Valve (6)
24 Volt 24 Volt (Hot) (Hot) Cool Heat (5)
24 Volt (Common)
Note: For 3-wire Zone Valve application, the thermostat SS/HP switch must be in the SS position position.
NEUTRAL 120VAC
24VAC HOT CLASS II TRANSFORMER
PART NO. 37-6754C www.white-rodgers.com
Replaces 37-6754B 0822
Diagramas de conexiones del termostato serie 80 para los modelos 1F80-0471 y 1F86-0471 Una sola etapa o bomba de calor Figura 1 – Sistema de una sola etapa o bomba de calor con un solo transformador Puente
O/B
Y
W
Vea la figura 3 Aplicación de válvula zonificada de 3 cables
Modo Cool
Modo Heat 1° etapa
Energizada constantemente en modo Cool o modo Heat
Energizada en llamada de calor o frío
G
RH
RC
C
24 voltios (Vivo) Calor
24 voltios (Vivo) Frío
Constante 24 voltios (neutro)
Sistema Una sola etapa excepto aplicación de válvula zonificada de 3 cables Bomba de calor
Soplador/ventilador circulador energizado N/A
NEUTRO 120VCA
24VCA VIVO TRANSFORMADOR CLASE II
Figura 2 – Sistema de una sola etapa o bomba de calor con dos transformadores Puente (ver nota)
Y
W
Vea la figura 3 Aplicación de válvula zonificada de 3 cables
Modo Cool
Modo Heat 1° etapa
Energizada constantemente en modo Cool o modo Heat
Energizada en llamada de calor o frío
O/B
G
RH
RC
C
24 voltios (Vivo) Calor
24 voltios (Vivo) Frío
Constante 24 voltios (neutro)
Sistema Una sola etapa excepto aplicación de válvula zonificada de 3 cables Bomba de calor
Soplador/ventilador circulador energizado N/A
NEUTRO 120VCA
24VCA NEUTRO 120VCA
VIVO
24VCA TRANSFORMADOR CLASE II
VIVO CALEFACCIÓN TRANSFORMADOR CLASE II
Nota: si desea iluminación constante de la luz de fondo o alimentación de entrada con cableado interno pero no desea que el sistema funcione en los modos HEAT y COOL, corte los cables de 24 V del transformador de calefacción y encíntelos. Conecte el circuito neutro desconectado del transformador de calefacción al circuito neutro del transformador de enfriamiento. Desconecte el cable a la terminal RH e instale un puente entre RH y RC. Según los requisitos del sistema, cambie el transformador de enfriamiento por un transformador de 75 VA clase II si es necesario.
Figura 3 – Conexiones de la válvula zonificada de sólo calor de 3 cables (SPDT) Puente
O/B
Y
W
G
Abre la válvula (4)
Soplador/ventilador circulador energizado
RH
RC
C
24 voltios (Vivo) Calor (5)
24 voltios (Vivo) Frío
Constante 24 voltios (neutro)
Sistema
Una sola etapa excepto aplicación de válvula zonificada de 3 cables
Cierra la válvula (6)
Nota: para aplicación de válvula zonificada de 3 cables, el interruptor SS/HP del termostato debe estar en la posición SS.
NEUTRO 120VCA
24VCA VIVO TRANSFORMADOR CLASE II
www.white-rodgers.com
N° DE PIEZA 37-6754C Reemplaza 37-6754B 0822